Glues & Tapes
-
- Out of Stock
Model Master Liquid Cement for Plastic
- $7.80
- Model Master 8872C is for plastic models joining polystyrene to polystyrene. It is quick drying and comes with a precision applicator in a 1/2 oz container.
- Read more
-
-
BSI112 Maxi-Cure Extra Thick CA Glue 1 oz.
- $6.99
- 1 oz. (29.5ml)plastic bottle. MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE’s Lexan. MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife
- Add to cart
-
BSI151 Insta-Set CA Accelerator 2 oz.
- $6.99
- 2 oz. (59ml) bottle INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed
- Add to cart
-
BSI107 Insta-Cure+ Gap Filling CA Glue 1 oz.
- $6.99
- 1 oz. (29.5ml) of INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close
- Add to cart
-
BSI102 Insta-Cure Super Thin CA Glue 1 oz.
- $6.99
- 102 insta-cure super thin cyanoacrylate glue 1 oz.
- Add to cart
-
BSI101 Insta-Cure Super-Thin CA Glue, 1/2oz
- $4.99
- BSI101 Insta-Cure Super-Thin Glue, 1/2oz.
- Add to cart
-
BS111 Maxi-Cure Extra Thick CA Glue 1/2 oz.
- $4.99
- 1/2 oz. (14.7ml). MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling
- Add to cart
-
BSI106 Insta-Cure+ Gap Filling CA Glue 1/2 oz.
- $4.99
- 1/2 oz (14.7ml) size. INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with
- Add to cart
-
- Out of Stock
BBG1002 White Hobby Glue 2X15ml
- $4.59
- Wood Glue 2 each 15ml tubes. White, non-toxic hobby-glue
- Read more
-
-
BSI161 Un-Cure CA Debonder 1 oz.
- $3.99
- 1 oz. (29.5ml) bottle. UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then
- Add to cart
-
BBG1001 White Hobby Glue
- $3.44
- Wood glue, one 15ml tube. White wood glue, non-toxic
- Add to cart
